scst/srpt

SCSI RDMA Protocol (SRP) Target driver for Linux
=================================================

The SRP target driver has been designed to work on top of the Linux
InfiniBand kernel drivers -- either the InfiniBand drivers included
with a Linux distribution of the OFED InfiniBand drivers. For more
information about using the SRP target driver in combination with
OFED, see also README.ofed.

The SRP target driver has been implemented as an SCST driver. This
makes it possible to support a lot of I/O modes on real and virtual
devices. A few examples of supported device handlers are:

1. scst_disk. This device handler implements transparent pass-through
   of SCSI commands and allows SRP to access and to export real
   SCSI devices, i.e. disks, hardware RAID volumes, tape libraries
   as SRP LUNs.

2. scst_vdisk, either in fileio or in blockio mode. This device handler
   allows to export software RAID volumes, LVM volumes, IDE disks, and
   normal files as SRP LUNs.

3. nullio. The nullio device handler allows to measure the performance
   of the SRP target implementation without performing any actual I/O.


Installation
------------

Proceed as follows to compile and install the SRP target driver:

1. To minimize QUEUEFULL conditions, apply the
   scst_increase_max_tgt_cmds patch as follows:

   cd ${SCST_DIR}
   patch -p0 < srpt/patches/scst_increase_max_tgt_cmds.patch

2. Now compile and install SRPT:

   cd ${SCST_DIR}
   make -s scst_clean scst scst_install
   make -s srpt_clean srpt srpt_install
   make -s scstadm scstadm_install

3. Edit the installed file /etc/init.d/scst and add ib_srpt to the
   SCST_MODULES variable.

4. Configure SCST such that it will be started during system boot:

   chkconfig scst on


Configuring the SRP Target System
---------------------------------

First of all, create the file /etc/scst.conf. Below you can find an
example of how you can create this file using the scstadmin tool:

  /etc/init.d/scst stop
  /etc/init.d/scst start

  scstadmin -ClearConfig /etc/scst.conf
  scstadmin -adddev disk01 -path /dev/ram0 -handler vdisk -options NV_CACHE
  scstadmin -adddev disk02 -path /dev/ram1 -handler vdisk -options NV_CACHE
  scstadmin -assigndev disk01 -group Default -lun 0
  scstadmin -assigndev disk02 -group Default -lun 1
  scstadmin -assigndev 4:0:0:0 -group Default -lun 2
  scstadmin -WriteConfig /etc/scst.conf
  cat /etc/scst.conf

Now load the new configuration:

  /etc/init.d/scst reload

Note: SCSI device ID's in host:ch:id:lun format can be obtained by
running the lsscsi command.


Configuring the SRP Initiator System
------------------------------------

First of all, load the SRP kernel module as follows:

  modprobe ib_srp

Next, discover the new SRP target by running the ipsrpdm command:

   ipsrpdm -c

Now let the initiator system log in to the target system:

   ibsrpdm -c | while read target_info; do echo "${target_info}" > /sys/class/infiniband_srp/${SRP_HCA_NAME}/add_target; done

Finally run lsscsi to display the details of the newly discovered SCSI disks:

   lsscsi

SRP targets can be recognized in the output of lsscsi by looking for
the disk names assigned on the SCST target ("disk01" in the example below):

[8:0:0:0]    disk    SCST_FIO disk01            102  /dev/sdb

Notes:
* You can edit /etc/infiniband/openib.conf to load srp driver and srp HA daemon
  automatically ie. set SRP_LOAD=yes, and SRPHA_ENABLE=yes
* To set up and use high availability feature you need dm-multipath driver
  and multipath tool
* Please refer to OFED-1.x SRP's user manual for more in-details instructions
  on how-to enable/use HA feature.


Performance notes
-----------------

In some cases, for instance working with SSD devices, which consume 100%
of a single CPU load for data transfers in their internal threads, to
maximize IOPS it can be needed to assign for those threads dedicated
CPUs using Linux CPU affinity facilities. No IRQ processing should be
done on those CPUs. Check that using /proc/interrupts. See taskset
command and Documentation/IRQ-affinity.txt in your kernel's source tree
for how to assign CPU affinity to tasks and IRQs.

The reason for that is that processing of coming commands in SIRQ context
can be done on the same CPUs as SSD devices' threads doing data
transfers. As the result, those threads won't receive all the CPU power
and perform worse.

Alternatively to CPU affinity assignment, you can try to enable SRP
target's internal thread. It will allows Linux CPU scheduler to better
distribute load among available CPUs. To enable SRP target driver's
internal thread you should load ib_srpt module with parameter
"thread=1".


Send questions about this driver to scst-devel@lists.sourceforge.net, CC:
Vu Pham <vuhuong@mellanox.com> and Bart Van Assche <bart.vanassche@gmail.com>.