* improve ResetTestRootWithChainID() concurrency safety
Rely on ioutil.TempDir() to create test root directories and ensure
multiple same-chain id test cases can run in parallel.
* Update config/toml.go
Co-Authored-By: alessio <quadrispro@ubuntu.com>
* clean up test directories after completion
Closes: #1034
* Remove redundant EnsureDir call
* s/PanicSafety()/panic()/s
* Put create dir functionality back in ResetTestRootWithChainID
* Place test directories in OS's tempdir
In modern UNIX and UNIX-like systems /tmp is very often
mounted as tmpfs. This might speed test execution a bit.
* Set 0700 to a const
* rootsDirs -> configRootDirs
* Don't double remove directories
* Avoid global variables
* Fix consensus tests
* Reduce defer stack
* Address review comments
* Try to fix tests
* Update CHANGELOG_PENDING.md
Co-Authored-By: alessio <quadrispro@ubuntu.com>
* Update consensus/common_test.go
Co-Authored-By: alessio <quadrispro@ubuntu.com>
* Update consensus/common_test.go
Co-Authored-By: alessio <quadrispro@ubuntu.com>
Earlier this week somebody posted this in GoS Riot chat:
```
E[2019-02-12|10:38:37.596] Corrupted entry. Skipping... module=consensus wal=/home/gaia/.gaiad/data/cs.wal/wal err="DataCorruptionError[length 878916964 exceeded maximum possible value of 1048576 bytes]"
E[2019-02-12|10:38:37.596] Corrupted entry. Skipping... module=consensus wal=/home/gaia/.gaiad/data/cs.wal/wal err="DataCorruptionError[length 825701731 exceeded maximum possible value of 1048576 bytes]"
E[2019-02-12|10:38:37.596] Corrupted entry. Skipping... module=consensus wal=/home/gaia/.gaiad/data/cs.wal/wal err="DataCorruptionError[length 1631073634 exceeded maximum possible value of 1048576 bytes]"
E[2019-02-12|10:38:37.596] Corrupted entry. Skipping... module=consensus wal=/home/gaia/.gaiad/data/cs.wal/wal err="DataCorruptionError[length 912418148 exceeded maximum possible value of 1048576 bytes]"
E[2019-02-12|10:38:37.600] Corrupted entry. Skipping... module=consensus wal=/home/gaia/.gaiad/data/cs.wal/wal err="DataCorruptionError[failed to read data: EOF]"
E[2019-02-12|10:38:37.600] Error on catchup replay. Proceeding to start ConsensusState anyway module=consensus err="Cannot replay height 7242. WAL does not contain #ENDHEIGHT for 7241"
E[2019-02-12|10:38:37.861] Error dialing peer module=p2p err="dial tcp 35.183.126.181:26656: i/o timeout
```
Note the length error messages. What has happened is the length field got corrupted probably. I've looked at the code and noticed that we don't check the msg size during encoding. This PR fixes that. It also improves a few error messages in WALDecoder.
* node: decrease retry conn timeout in test
Should fix#3256
The retry timeout was set to the default, which is the same as the
accept timeout, so it's no wonder this would fail. Here we decrease the
retry timeout so we can try many times before the accept timeout.
* p2p: increase handshake timeout in test
This fails sometimes, presumably because the handshake timeout is so low
(only 50ms). So increase it to 1s. Should fix#3187
* privval: fix race with ping. closes#3237
Pings happen in a go-routine and can happen concurrently with other
messages. Since we use a request/response protocol, we expect to send a
request and get back the corresponding response. But with pings
happening concurrently, this assumption could be violated. We were using
a mutex, but only a RWMutex, where the RLock was being held for sending
messages - this was to allow the underlying connection to be replaced if
it fails. Turns out we actually need to use a full lock (not just a read
lock) to prevent multiple requests from happening concurrently.
* node: fix test name. DelayedStop -> DelayedStart
* autofile: Wait() method
In the TestWALTruncate in consensus/wal_test.go we remove the WAL
directory at the end of the test. However the wal.Stop() does not
properly wait for the autofile group to finish shutting down. Hence it
was possible that the group's go-routine is still running when the
cleanup happens, which causes a panic since the directory disappeared.
Here we add a Wait() method to properly wait until the go-routine exits
so we can safely clean up. This fixes#2852.
* fix Group.RotateFile need call Flush() before rename. #2428
* fix some review issue. #2428
refactor Group's config: replace setting member with initial option
* fix a handwriting mistake
* fix a time window error between rename and write.
* fix a syntax mistake.
* change option name Get_ to With_
* fix review issue
* fix review issue
Alessio TregliaandAnton Kaliaev
Ethan BuchmanandGitHub
Thane ThomsonandAnton Kaliaev
goolAdapterandAlexander Simmerl
Zarko MilosevicandEthan Buchman
Dev OjhaandAnton Kaliaev
Jae Kwon
Emmanuel Odeke