Add "IncrementalBytes" field to status of DataDownload and PVR to indicate data transferred by the incremental restore
Signed-off-by: Wenkai Yin(尹文开) <yinw@vmware.com>
* Update CRDs and CLI to support in-place restore (#10038)
Update CRDs(Restore, DataDownload, PodVolumeRestore) and restore create CLI to support in-place restore
Signed-off-by: Wenkai Yin(尹文开) <yinw@vmware.com>
* Update Kopia(filesystem) uploader to support incremental and deleteExtraFile during restore (#10066)
Update Kopia(filesystem) uploader to support incremental and deleteExtraFile during restore
Signed-off-by: Wenkai Yin(尹文开) <yinw@vmware.com>
* Update Restore Exposer and PVC CSI to support in-place restore (#10104)
1. Update Restore Exposer to support exposing with existing PV for in-place restore
2. Update PVC CSI RIA to continue the restore process for in-place restore
Signed-off-by: Wenkai Yin(尹文开) <yinw@vmware.com>
* Update Block uploader to support increase restore (#10244)
Update Block uploader to support increase restore
Signed-off-by: Wenkai Yin(尹文开) <yinw@vmware.com>
* Update Exposer to recreate the target PV if the volume mode is different with the restore PVC (#10257)
Update Exposer to recreate the target PV if the volume mode is different with t
he restore PVC
Signed-off-by: Wenkai Yin(尹文开) <yinw@vmware.com>
* Preserve PVC selected-node annotation via carrier annotation for in-place restore
For in-place volume data restore, the existing PVC is deleted and
recreated. For StorageClasses with the WaitForFirstConsumer volume
binding mode, losing the volume.kubernetes.io/selected-node annotation
could let the scheduler place the recreated workload Pod in a different
zone than the original PV, leaving it stuck in ContainerCreating.
Instead of relying on RestoreItemAction execution order (the generic
PVC RIA unconditionally strips the selected-node annotation), the PVC
CSI RIA now captures the annotation from the existing PVC right before
deleting it and carries it on the target PVC via the Velero-internal
restore.velero.io/inplace-restore-selected-node annotation. The restore
engine translates the carrier back to the Kubernetes annotation after
all RestoreItemActions have run and always strips the carrier so it
never lands on the cluster.
This makes the behavior independent of RIA ordering: the Kubernetes
annotation is stripped by default on every path (including when the
target PVC does not exist and Velero falls back to provisioning a new
PVC), and preservation only happens when the CSI RIA explicitly
captured a value from the existing PVC.
Signed-off-by: chlins <chlins.zhang@gmail.com>
* Update the control path to make the in-place incremental restore with block data mover work E2E (#10410)
Update the control path to make the in-place incremental restore with block data mover work E2E
Signed-off-by: Wenkai Yin(尹文开) <yinw@vmware.com>
---------
Signed-off-by: Wenkai Yin(尹文开) <yinw@vmware.com>
Signed-off-by: chlins <chlins.zhang@gmail.com>
Co-authored-by: chlins <chlins.zhang@gmail.com>
getParentBackupInfo's parent-selection log lines interpolated the
parentSnapshot parameter. On the discovery branch (no explicit parent
passed by the caller) that parameter is empty by definition, so every
message about which parent was chosen, or why a run fell back to full,
printed no identifier at all -- e.g. "Using parent snapshot , start
time ...". This is the normal path for scheduled/incremental backups,
so the omission hit the common case, not an edge one.
Bind a parentID local that starts as the parameter but is overwritten
once a parent is actually resolved (explicit or discovered), and log
that instead. No behavior change.
Signed-off-by: Tiger Kaovilai <tkaovila@redhat.com>
Co-authored-by: Claude Fable 5 <noreply@anthropic.com>
* Detect block uploader cancellation through wrapped errors
Cancelling a block data mover backup was reported as a failure: the
DataUpload ended Failed with an error message and the Backup went
PartiallyFailed, for a user-requested cancel.
The cause is a sentinel equality check. block.ErrCanceled is raised in
the write loop and then wrapped twice before it reaches the provider --
once in block/uploader.go ("error backing up bdev %s") and again in
block/snapshot.go ("Failed to run uploader backup for si %v") -- so
`err == block.ErrCanceled` can never be true and the ErrorCanceled
returns are unreachable. The filesystem provider avoids this by asking
the uploader for its state (kpUploader.IsCanceled()) rather than
inspecting the error.
Use errors.Is at both the backup and restore sites.
Adds TestBlockProviderCancelThroughWrappedError, which injects the
doubly-wrapped sentinel exactly as production builds it. Note the
assertion is require.ErrorIs, not ErrorContains: provider.ErrorCanceled
and block.ErrCanceled carry identical message text, so a substring
assertion passes whether or not the sentinel was recognised -- which is
why the existing test, injecting the bare sentinel, did not catch this.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Signed-off-by: Tiger Kaovilai <tkaovila@redhat.com>
(cherry picked from commit 9d6c5da7a893068d424b0c7896638787c636e213)
Signed-off-by: Tiger Kaovilai <tkaovila@redhat.com>
* Add changelog for #10308
Signed-off-by: Tiger Kaovilai <tkaovila@redhat.com>
* lint: fix misspelling (recognised -> recognized)
Signed-off-by: Tiger Kaovilai <tkaovila@redhat.com>
---------
Signed-off-by: Tiger Kaovilai <tkaovila@redhat.com>
Co-authored-by: Claude Fable 5 <noreply@anthropic.com>
* Add change-id and volume-id retrieve logic for both vks and vanilla k8s environment.
* Add change-id and volume-id support code in exposer.
Signed-off-by: Xun Jiang <xun.jiang@broadcom.com>
Lyndon-Li
Wenkai Yin(尹文开)andGitHub
Jay2006sawant
lyndon-liandGitHub
Xun Jiang/Bruce JiangandGitHub
Xun Jiang